Stan A PE
Structural Engineer/Project Engineer
EDUCATION: BSCE from University of Illinois @ Urbana
REGISTERED PROFESSIONAL ENGINEER IN NEW YORK
EMPLOYMENT HISTORY
09/11 TO 04/12: Bechtel Power Corporation. Frederick, MD
Position: Structural Engineer
Turkey Point Power Plant: Temporary assignment through Talascend as a design engineer for evaluation of existing structural turbine building steel floor beams for updated loads from piping. Evaluation of existing Concrete Masonry walls for tornado generated missiles and tornado generated wind loads for an existing structure which is upgraded to a Class 1 structure.
04/10 TO 01/11: Bechtel Power Corporation. Frederick, MD
Position: Structural Engineer
St Lucie Power Plant: Temporary assignment through Talascend as a design engineer for evaluation of existing structural steel floor beams and columns of the turbine building. Evaluated temporary construction loading and new loads from relocated equipment and piping for the Florida Power & Light Hutchinson Plant Power Uprate Project. Evaluation of temporary rigging for construction installation of equipment. Review of vendors’ calculations for new equipment, support racks and temporary buildings. Primary duties consisted of structural re-evaluation of existing structural systems using the original codes of record for the plant and current building codes for new or temporary work. Structural analysis was done using STAAD and MathCAD computer programs.
10/07 TO 08/08: Bechtel Power Corporation. Frederick, MD
Position: Structural Engineer
Temporary assignment through EPC Global as a design engineer for structural steel and concrete design for the coal fired Sammis Power Plant FGD Project. Shallow and deep foundation designs: mat foundations and pile foundation design. Primary duties are structural design in steel and concrete using the IBC code. Structural analysis and design using STAAD and MathCAD computer programs. Design of foundations for transformer containment pits.
Calculation review of structural pile supported foundations.
Calculation review of structural steel design (STAAD Analysis) 130 feet high concentric braced frame supporting FGD ducts.
4/2006- 4/30/07 Temporary assignment through EPC Global for the Comanche Peak Steam Electric Station Unit 1 Steam Generator Replacement Project. Design of shallow mat foundations for the construction of the temporary lift system (movable crane on rails and its supporting structures) for the replacement of 4 steam generators. Review of existing containment polar crane capacity for the new lift loads that were above the rated lifting capacity of the crane. Design of temporary 32” diameter main steam pipe supports on the existing piping to facilitate the removal and replacement of steam generators: includes main steam pipe fixed supports, springs and temporary pipe support construction to permit safe removal of the existing steam generators. Evaluation of existing steel embedment anchorages for the new steam generators for increased design loads. Qualify and re-evaluate the structural internal structural concrete walls and slabs for the reaction loads (embedment anchorage) from the new steam generators. Revise the client’s original calculations to qualify the adequacy of the new steam generator embedment anchorages for the revised thermal, Seismic and LOCA loads.
11/04- 4/06: Sargent & Lundy Engineers. Chicago, IL & American Electric Company. Columbus, OH
Position: DESIGN ENGINEER
Temporary assignment as a design structural engineer for structural steel and concrete design for coal fired plants. Shallow and deep foundation designs at coal fired electric power plants. Spread footings and pile foundation design. Primary duties are structural design in steel and concrete with the IBC code. Structural analysis and design using SAFE, STAAD and MathCAD computer programs.
4/03-6/04: Virginia Dominion Power. Richmond, VA
Position: DESIGN ENGINEER
Temporary assignment as a design structural engineer for the evaluation of an existing concrete fuel pool structure 136’x41’x42.5’ deep and its steel superstructure for revised load conditions. Loading consisting of dead, live, earthquake, hydrostatic, and hydrodynamic loads along with other load conditions. Using SAP 2000 computer program and MathCAD program to originate calculations. Other short assignments: reanalysis and remediation of partly failed foundation for a two story steel frame service building.
3/00- 12/02: Sargent & Lundy Engineers. Chicago, Ill.
Position: DESIGN ENGINEER
Design structural engineer for structural steel and concrete design for coal fired plants and single cycle combustion turbine plants, existing power plant modifications and evaluation of existing structural systems. Design support for selective catalytic converters, (SCR). Shallow and deep foundation designs at coal fired electric power plants. Spread footings and drilled pier foundation design. Switchyard structures and prefabricated building foundation design. Primary duties are structural design in steel and concrete with UBC or BOCA codes. Structural analysis and design using SAFE, STAAD and MathCAD computer programs.
9/97- 3/00: Peak Technical Services & Aerotek Technical Services Position: DESIGN ENGINEER
Cities: Detroit, Syracuse, Washington and Las Vegas
Assisted as a contract design structural engineer for industrial, commercial and institutional projects consisting of the following: industrial building modifications, one story industrial structures, 1 to 2 story institutional high school buildings and a 2 story convention center building addition among other structural work assignments.
6/96-9/97: Peak Technical Services/Detroit Edison Company. Detroit, Mi
DESIGN ENGINEER
Design structural engineer for architectural and structural engineering projects at the Detroit Edison coal fired electric power plants. Design of 2 story addition to existing control building, structural evaluation of fossil plant structural systems such as bracing systems, floor vibration analysis, revised floor loading, small steel framing, steel platforms. Major project work such as precipitator ducts structural steel internals, 80'x60'x10' depth; 30' telecommunication tower mounted
Stan A Szymanowski PE Page 2
on existing roof; specification writing for the performance specification for a chimney liner replacement, exterior metal curtain walls, demolition specifications and drawings, concrete retaining walls, plant emergency repairs.
02/93 to 06/96: EI ASSOCIATE and R&D ENGINEERING. Buffalo, NY
Position: DESIGN ENGINEER
Structural engineer for several building projects for EI associates consisting of a 3rd floor addition to the Bristol Myers Building in Syracuse NY. Designed the structural framing and roofing system for a 20000 sq. ft addition to an existing building. Design of a mezzanine floor for additional floor space office for Air Sep Corporation. Precast floor system supported on a structural ste...
Login or Register to view the full resume.
